We use cookies on our website to ensure that we give you the best user experience.
By continuing to browse our site, you are agreeing to the use of our COOKIES POLICY. Learn more
I understand
International Test Standards and Methods : Compression
Compressibility and Recovery
ASTM-C972 – Standard Test Method for Compression-Recovery of Tape Sealant
ASTM-D5672 – Standard Test Method for Testing Flexible Cellular Materials Measurement of Indentation Force Deflection Using a 25-mm (1-in.) Deflection Technique
ASTM-F1566 – Standard Test Methods for Evaluation of Innersprings, Boxsprings, Mattresses or Mattress Sets
BS ISO-7322 – Composition cork. Test methods
IEC-60371-2 – specification for insulating materials based on mica - part 2 methods of test
Compressive Deformation
EN-826 – Thermal insulating products for building applications - determination of compression behaviour
Compressive Hardness
ASTM-D143 – Standard Test Methods for Small Clear Specimens of Timber
ASTM-D3574 – Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams
ASTM-F1839-08 – Standard Specification for Rigid Polyurethane Foam for Use as a Standard Material for Testing Orthopaedic Devices and Instruments
Compressive Strength
ASTM-D143 – Standard Test Methods for Small Clear Specimens of Timber
ASTM-D2061-07 – Standard Test Methods for Strength Tests for Zippers
ASTM-D5379 – Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method
ASTM-D575 – Standard Test Methods for Rubber Properties in Compression
ASTM-D6534 – Standard Test Method for Determining the Peak Force-to-Actuate a Mechanical Pump Dispenser
ASTM-E1012 – Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM-E9 – Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature
ASTM-F1839-08 – Standard Specification for Rigid Polyurethane Foam for Use as a Standard Material for Testing Orthopaedic Devices and Instruments
BS-1726-1 – Cylindrical helical springs made from round wire and bar. Guide to methods of specifying and tolerancing hot coiled springs, and cold coiled springs not covered by BS EN 15800, and general spring testing. Part 1, compression springs
BS-373 – Methods of testing small clear specimens of timber
BS EN-1125 – Building hardware. Panic exit devices operated by a horizontal bar, for use on escape routes. Requirements and test methods.
BS EN-12209 – Building hardware. Locks and latches. Mechanically operated locks, latches and locking plates. Requirements and test methods
BS EN-12365-2 – Building hardware. Gasket and weatherstripping for doors, windows, shutters and curtain walling. Linear compression force test methods
BS EN-14488-2 – Testing sprayed concrete. Compressive strength of young sprayed concrete
BS EN-179 – Building hardware. Emergency exit devices operated by a lever handle or push pad, for use on escape routes. Requirements and test
BS EN-2591-408 – Aerospace series. Elements of electrical and optical connection. Test methods. Mating and unmating forces
BS EN-2591-412 – Aerospace series. Elements of electrical and optical connection. Test methods. Contact insertion and extraction forces
BS EN-2591-418 – Aerospace series. Elements of electrical and optical connection. Test methods. Gauge insertion/extraction forces (female contacts)
BS EN-2591-420 – Aerospace series. Elements of electrical and optical connection. Test methods. Mechanical strength of rear accessories
BS EN-3841-509 – Aerospace series. Circuit breakers. Test methods. Insertion and extraction forces of signal contact terminals
BS EN-61212-2 – Insulating materials. Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes. Methods of test
BS EN-61300-3-11 – Fibre Optic Interconnecting Devices and Passive Components - Basic Test and Measurement Procedures Part 3.11: Examinations and Measurements - Engagement and Separation Forces
BS EN-61300-3-22 – Fibre optic interconnecting devices and passive components - Basic test and measurement procedures Part 3-22: Examinations and measurements - Ferrule compression force
BS EN ISO-10555-5 – Intravascular catheters. Sterile and single-use catheters. Over-needle peripheral catheters
BS EN ISO-23907 – Sharps Injury Protection. Requirements and test methods. Sharps containers
BS EN ISO-7886-1 – Sterile hypodermic syringes for single use. Syringes for manual use
BS EN ISO-844 – Rigid cellular plastics. Determination of compression properties
DIN-2192 – Flat form springs - Quality requirements
DIN EN-14488-2 – Testing sprayed concrete - Part 2: Compressive strength of young sprayed concrete
EN-826 – Thermal insulating products for building applications - determination of compression behaviour
FEFCO-4-6,8,11,50,55 – Introduction to the development of FEFCO Testing Methods for corrugated board and boxes
IEC-60512-13-1 – Connectors for electronic equipment - Tests and measurements - Part 13-1: Mechanical operation tests - Test 13a: Engaging and separating forces
ISO-20344 – Personal protective equipment - Test methods for footwear
ISO-20345 – Personal protective equipment - Safety footwear
TAPPI-T 821 – Pin adhesion of corrugated board by selective separation
Concora Crush (CCT)
TAPPI-T 824 – Fluted edge crush of corrugating medium (flexible beam method)
Concora Medium (CMT)
TAPPI-T 809 – Flat crush of corrugated medium (CMT test)
Edge Crush (ECT)
ASTM-C364 – Standard Test Method for Edgewise Compressive Strength of Sandwich Constructions
FEFCO-4-6,8,11,50,55 – Introduction to the development of FEFCO Testing Methods for corrugated board and boxes