International Test Standards and Methods : Pull-off / Pull-out

Butt Joint

• ASTM-C633 – Standard Test Method for Adhesion or Cohesion Strength of Thermal Spray Coatings
• ASTM-D2095 – Standard Test Method for Tensile Strength of Adhesives by Means of Bar and Rod Specimens
• ASTM-D897 – Standard Test Method for Tensile Properties of Adhesive Bonds
• ASTM-F1147 – Standard Test Method for Tension Testing of Calcium Phosphate and Metallic Coatings
• BS EN-15870 – Adhesives. Determination of tensile strength of butt joints
• BS EN ISO-4624 – Paints and varnishes. Pull-off test for adhesion
• ISO-6922 – Adhesives - Determination of tensile strength of butt joints

Parallel Plate Adhesion

• ASTM-D3354 – Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method
• ASTM-D429 – Standard Test Methods for Rubber Property—Adhesion to Rigid Substrates
• ISO-11502 – Plastics - Film and sheeting - Determination of blocking resistance

Pull-off / Pull-out

• ANSI/EIA-364-38B – Cable pull-out test procedure for electrical connectors
• ASTM-B571-97 – Standard Practice for Qualitative Adhesion Testing of Metallic Coatings
• ASTM-B913 – Standard Test Method for Evaluation of Crimped Electrical Connections to 16-Gauge and Smaller Diameter Stranded and Solid Conductors
• ASTM-C297 – Standard Test Method for Flatwise Tensile Strength of Sandwich Constructions
• ASTM-C907 – Standard Test Method for Tensile Adhesive Strength of Preformed Tape Sealants by Disk Method
• ASTM-D143 – Standard Test Methods for Small Clear Specimens of Timber
• ASTM-D2061-07 – Standard Test Methods for Strength Tests for Zippers
• ASTM-D2979-01 – Standard Test Method for Pressure-Sensitive Tack of Adhesives Using an Inverted Probe Machine
• ASTM-D4541 – Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
• ASTM-D6958 – Standard Test Methods for Evaluating Side-Bonding Potential of Wood Coatings
• ASTM-D7257-06 – Standard Test Method for Automated Shelling Two-Piece Child-Resistant Closures That Are Activated by Two Simultaneous Dissimilar
• ASTM-D7834 – Standard Test Method for Filling Material Shedding of Paint Brushes
• ASTM-D816 – Standard Test Methods for Rubber Cements
• ASTM-F1839-08 – Standard Specification for Rigid Polyurethane Foam for Use as a Standard Material for Testing Orthopaedic Devices and Instruments
• ASTM-F543 – Standard Specification and Test Methods for Metallic Medical Bone Screws
• ASTM-F564 – Standard Specification and Test Methods for Metallic Bone Staples
• BS-1881-207 – Testing concrete. Recommendations for the assessment of concrete strength by near-to-surface tests
• BS-5G 178-1 – Crimped joints for aircraft electrical cables and wires. Specification for design requirements (including tests) for components and tools
• BS-7907 – Code of practice for the design and manufacture of children's clothing to promote mechanical safety
• BS EN-1400 – Child use and care articles. Soothers for babies and young children. Safety requirements and test methods
• BS EN-14350-1 – Child use and care articles. Drinking equipment. General and mechanical requirements and tests
• BS EN-2243-4 – Aerospace series. Non-metallic materials. Structural adhesives. Test method. Metal-honeycomb core flatwise tensile test
• BS EN-2591-408 – Aerospace series. Elements of electrical and optical connection. Test methods. Mating and unmating forces
• BS EN-2591-412 – Aerospace series. Elements of electrical and optical connection. Test methods. Contact insertion and extraction forces
• BS EN-2591-417 – Aerospace series. Elements of electrical and optical connection. Test methods. Tensile strength (crimped connection)
• BS EN-2591-418 – Aerospace series. Elements of electrical and optical connection. Test methods. Gauge insertion/extraction forces (female contacts)
• BS EN-2591-420 – Aerospace series. Elements of electrical and optical connection. Test methods. Mechanical strength of rear accessories
• BS EN-2591-709 – Aerospace series. Elements of electrical and optical connection. Test methods. Electrical elements. Tensile strength of couplers
• BS EN-3841-509 – Aerospace series. Circuit breakers. Test methods. Insertion and extraction forces of signal contact terminals
• BS EN-50289-3-17 – Communication cables. Specifications for test methods. Mechanical test methods. Adhesion of dielectric and sheath
• BS EN-5057 – Specification for flat, quick-connect terminations
• BS EN-60352-2 – Solderless connections. Crimped connections. General requirements, test methods and practical guidance
• BS EN-61300-2-4 – Fibre optic interconnecting devices and passive components - Basic test and measurement procedures Part 2-4: Tests - Fibre/cable
• BS EN-61300-3-11 – Fibre Optic Interconnecting Devices and Passive Components - Basic Test and Measurement Procedures Part 3.11: Examinations and Measurements - Engagement and Separation Forces
• BS EN-61300-3-33 – Fibre optic interconnecting devices and passive components - Basic test and measurement procedures Part 3-33: Examinations and measurements - Withdrawal force from a resilient alignment sleeve using gauge pins
• BS EN ISO-11608-2 – Needle-based injection systems for medical use. Requirements and test methods. Needles
• BS ISO-4919 – carpets - determination of tuft withdrawal force
• DEF-STAN 59-71 – Crimped electrical connectors for copper conductors
• DIN-3419-1 – Slide fasteners - Part 1: Technical delivery conditions
• DIN-41611-4 – Solderless electrical connections; clip connections; terminology, requirements, testing
• DIN-46249 – Snap-on connectors, non insulated; requirements, tests
• DIN EN-61238-1 – Compression and mechanical connectors for power cables for rated voltages up to 36 kV (Um = 42 kV) - Part 1: Test methods and requirements (IEC 61238-1:2003)
• IEC-60512-13-1 – Connectors for electronic equipment - Tests and measurements - Part 13-1: Mechanical operation tests - Test 13a: Engaging and separating forces
• ISO-1966 – Crimped joints for aircraft electrical cables
• ISO-2409 – Paints and varnishes - Cross-cut test
• ISO-9727-5 – Cylindrical cork stoppers - Physical tests - Part 5: Determination of extraction force
• NASA-STD-8739.4 – crimping, interconnecting cables, harnesses, and wiring
• UL-486A – Wire connections and soldering lugs for use with copper conductors

 

See Mecmesin’s range of pull-off/pull-out testers

Previous page